Skip to content
CleaningHQSearch

Robot vacuum

Hair in the brushes and bearings is the main threat. Makers disagree about the filter: Roborock's is rinsed, iRobot's is not designed to be washed.

What not to do

Sodium hypochlorite (chlorine bleach) is ruled out by the manufacturer for robot vacuum

Best avoided

The available guidance advises against this.

Roborock's warning for the main brush of its S7.

Evidence

Strongly supported

Sources

  1. Roborock S7 robotic vacuum cleaner user manual

    Roborock · Manufacturer documentation

    Relied on for: That corrosive detergent or disinfectant must not be used on the main brush. (states this directly)

Precautions

  • Disconnect from the power supply first
  • Check the manufacturer's instructions

Start here

What this is, what tends to go wrong with it, and what to do about it.

Which part are you cleaning?

These parts take different answers. Cleaning one the way you clean another is a common way to damage this.

  • Robot vacuum filter

    Check before you rinse it. Roborock's S7 filter is washable, while iRobot says its filters are not designed to be washed.

  • Robot vacuum sensors and contacts

    Roborock and iRobot both wipe cliff sensors with a dry cloth. They differ on charging contacts, so do not swap one maker's method for another's.

In detail

Most robot vacuum care is clearing hair and keeping sensors clean, but the makers differ, so check which rules apply to yours. Hair is the main concern. iRobot says excessive build-up can permanently damage a Roomba, and that a front wheel clogged with hair and debris can damage floors. Take out the brushes regularly and clear the bearings at each end. Roborock wants the same for its S7. The filter is where makers disagree. Roborock's is washable: rinse it, tap the frame, avoid touching it with hands, brushes or sharp objects, and let it dry thoroughly. iRobot says to tap its filters clean and that they are not designed to be washed. Roborock's other limits are specific. Switch the robot off first. Wipe the main brush with a wet cloth and dry it out of direct sun. Do not use corrosive detergent or disinfectant on it. Rinse the dustbin with fresh water only, with no cleaning liquid, to avoid blockages. Use a soft dry cloth on the sensors and charging contacts, and never wipe the contacts with a wet cloth. iRobot also says to wipe cliff sensors with a clean dry cloth. Roborock also says not to run the robot over burning objects, such as cigarette ends, or over glass and nails.

Parts
Robot vacuum filter, Robot vacuum sensors and contacts

Sources for this page

Sources

  1. Roborock S7 robotic vacuum cleaner user manual

    Roborock · Manufacturer documentation

    Relied on for: Roborock's maintenance steps, chemical limits and what it must not be run over. (states this directly)

  2. Roomba robot vacuum maintenance

    iRobot · Manufacturer documentation

    Relied on for: iRobot's filter, hair, wheel and sensor guidance. (states this directly)

Share this page
Parts of a robot vacuum to cleanThe underside of a round robot vacuum with six numbered parts: the side brush, the main brush and its bearings, the front wheel, the cliff sensors around the edge, the charging contacts, and the dustbin and filter at the back.123456
  1. Side brush. Clear hair. Roborock's unscrews.
  2. Main brush and bearings. Clear hair from both ends.
  3. Front wheel. Clear debris, which iRobot says can mark floors.
  4. Cliff sensors. Clean dry cloth.
  5. Charging contacts. Follow your maker. Roborock says never wet.
  6. Dustbin and filter. Roborock's is rinsed. iRobot's is not washed.
Based on Roborock's S7 manual and iRobot's Roomba guidance. Parts sit in different places on different robots. Diagram by CleaningHQ.

Parts that need different treatment

Each of these needs its own care, so advice for the whole appliance will not fit them all.

More around the house

All around the house